I'm just... I'm not sure what they are doing. It's not even an RC10 adjacent design. They just licensed the old Tamiya Fox design and put new stickers on it? Really?

MJX has a few well-reviewed 1:14 rally cars. They've got a restomod truck (inspired by Ken Block's Hoonitruck), a Lancia Delta Integrale inspired car, a licensed Citroen C3, and most recently a licensed Volkswagen Polo 2015-inspired car.

These cars are all essentially identical. They've got the same chassis and power systems (minor updates incl. with the Volkswagen but overall same performance), and the only real differences between the 4 small rally cars under the polycarbonate shell are the shapes of the bumpers and the rear diffuser.

However, in 2025 MJX significantly broadened their rally car range by introducing the Citroen and Volkswagen cars in two new scales: 1:10 and 1:7.

I just received my 1:10 Volkswagen rally and... hoo boy, they've introduced a lot of innovations.

First let's get pricing out of the way: I ordered the car from AliExpress, and it was fulfillment from a US fulfillment center for $206 for the no-battery package. Final cost after taxes & such was about $227. I received it 6 days after ordering.

Of course, it has what you expect in a scaled-up MJX: a great preinstalled light system, plush suspension with beefy metal CVDs on each corner.

But there are so many refinements. The ESC is rated for 3S/80A, has an XT60 connector, and it's now officially branded with MJX's in-house brand, "Angry Snail". The 3652 motor and ESC are sensored, using a barrel plug similar to the Hobbywing style.

And yes, the power is silky smooth. I noticed it immediately at low speeds.

The radio looks to be pretty generic, now branded MJX with the model "T3D" that uses 4AA instead of 2. I'm not noticing the throttle lag that MJXes are famous for, but that could also be because I adjust the trim on my throttles to start on a hair trigger. Standard MJX gyro is included to make holding a line easier.

The chassis is an aluminum plate, now embossed with the actual name of the company, Guangdong Meijiaxin.

The car uses a clipless design that hooks into the front shock tower and fastens with magnets and a single body post and pin in the back. As you can see in the pictures, the body post sticks out of the diffuser, toward the ground. This... seems... extremely prone to problems, but I've run the car over asphalt and gravel now with no apparent damage. I guess we'll see. The RTR package includes parts for body post conversion, as well as extra rod ends and extra shock springs.

Lights are powered through a pin connector that automatically engages and disengages when the body is attached and removed. No hanging wires.

And performance is fantastic. I'm no road-car expert, but I felt like the Volkswagen rally found a good middle ground between my Vendetta (launches like an arrow off a bow, steers like a brick), and the 1:14 rally cars (twitchy, easy to slide out, easy to roll). By comparison to the smaller cars, the Volkswagen cuts some tight turns without sliding quite as severely, but it will never catch a dedicated drag racer.

Notably missing in this design is any kind of slipper clutch or center diff. The spur-directly-on-center-driveshaft design really worked well in the 1:14 scale, but I guess we'll have to see if the 1:10 scale will be as durable. The car isn't really designed for big air or hard landings, so maybe a center diff would be overkill.

Now that I've had a few outings on 2S and 3S packs, here is my overall assessment:

• The brushless system (supposedly 4400kV) is crazy fast.

• As shipped, the truck is really slammed, and does NOT want to wheelie or come off the ground. On 2S, I couldn't get it to lift at all in straight-line acceleration. On 3S, I had to lift the truck with the shock collar adjusters to get it to flip on takeoff.

• I'm not sure why, maybe it's the higher top speed & slightly longer wheelbase, but it is a bit harder to maneuver than the smaller trucks. I was getting the hang of it after a couple of packs, but you definitely need to finesse the throttle to keep it from rolling in turns. Go in too hot and it will surely roll. It could also be the tires, which were very sticky out of the box and may get a little less aggressive as they wear down.

• Jumping was fine from a speed/height standpoint. I was struggling with air control but I'm not very good at that anyway. My landings tumbled but it ended up on 4 wheels.

• Quite a few tumbles but no damage.

So I've been buying these Hyper Gos based largely on the recommendations of Tomley RC almost since they first came out. I've got two of the 1:16 models, the 16207 buggy and 16209 monster truck, and one of the 1:14 scale street bashers, the 14302 Lancia-lookalike rally car.

The 1:16 scale off roaders are damn near indestructible. I've been running both of them on 3S for more than a year, and not one single thing has broken except for some body cracks (easily addressed by trimming the body back and reinforcing with tape).

The one complaint that most owners have with these small trucks is the small battery tray. You either buy extended parts to raise the retaining arm for the battery tray, or you remove the retaining arm entirely and hack together your own solution with velcro straps. Or, just bite the bullet and use the largest 3S pack that will fit the out-of-box tray. The best I could find is a 3S 1300mah Gens Ace that fits like it was made for it. That's still plenty for 11 or 12 minutes of full on hooning, or half an hour of on-and-off trail trucking.

The 14210 monster truck follows on the design of the 1:14 scale street bashers with a similar flat metal chassis plate design with a wheelbase a couple cm longer than the 1:16 scale trucks. It has a LOT more space for the battery, and it can fit 3S 2000mah packs or 2S 3000mah packs out-of-the-box. The servo is no longer parked under the ESC, and can be separately upgraded without taking the whole thing apart. RX has been moved into a dedicated waterproof box. Tires are slightly larger than the 1:16 scale trucks. All welcome updates!

MJX has corrected a lot of the problems that early Youtubers identified:

• Rear CVDs have been upgraded to sliding driveshafts anchored at both ends, no risk of a dogbone end popping out.

• Several screws on the model have been replaced with flange head screws, where Youtubers had noted there was risk of the parts pulling off over the screw heads.

• The "super speed mode" on the ESC has been eliminated. Looks like it's running full power right out of the box.

• The 2S Li-Ion cylindrical batteries used in the initial release have been upgraded to regular flat-pack LiPos.

Other first impressions:

• The shocks (metal bodies, metal caps, threaded) are large and buttery smooth for a model of this size. Out of the box, the model squats pretty low, like a Talion or similar truggy. But the kit comes with free stiffer shock springs if you want to push it up into a more traditional monster track stance.

• The 14302 rally car had a problem where gravel could slip into the joints of the suspension arms, effectively jamming the suspension. Those gaps have been filled with solid plastic on the 14210.

• The two included bodies (black and gold) are pre-installed with hard plastic sliders for durability.

• The servo saver is really, really soft. It's built into the servo horn, so I'm not sure if it's adjustable. We'll see how it performs.

• The 30 page manual is surprisingly comprehensive for an RTR Chinese import, with detailed exploded diagrams & part numbers for all subsystems on the truck.

I picked mine up on Amazon for $170, but if you're willing to wait a couple of weeks, you can find them on AliExpress from reputable sellers for about $155.

Rady Children's Hospital in San Diego has remote controlled power wheels-style cars used to transport kids around the hospital.

Getting into it all and enjoying myself. As a fan of spec racing this buggy caught my attention, it is the brushed variant but still has plenty of power for having fun.

I love the slash, it is such a fun car to drive and bash. I installed the Traxxas light kit. My friend burnt out his spur gear, so I gave him mine and 3d printed a 90T.... noisy, but it works well enough.

Bought a Duratrax work stand but honestly not happy with it. It's not tall enough (the wheels touch the workbench even when the car is on the stand) and the "trough" in the middle isn't deep enough to accommodate the TRX-4 transmission, drive shafts, and links, so the model kind of wobbles around balanced on its transmission.

Are there any commercial stands out there that can hold a heavy TRX-4 off the bench, and easily rotate it?

I'm almost at the point of buying some lumber and making something.

It's a fun 4wd kit. Can't wait to get the boomerang rerelease this year. That was my dream RC kit and never had one

I just like this picture

I hit the trail a couple months ago with this car. It's a total beast and fun to drive. I wish Holmes Hobbies would quit hinting at new brushed motors for it and release one already!

This thing looks pretty sweet. $549 is a bit out of my price range currently, but cool to see something new hit the market. Anyone plan on getting one or have experience with RC bikes?